HOW TO INSTALL A TUB (STEP BY STEP).

How to Install a Tub (Step By Step).

How to Install a Tub (Step By Step).

Blog Article

Pricing

What are your thoughts and feelings about How to Install a Bathtub Yourself?


Tools You Need to Install a New Bathtub
Setting up a bath tub isn't precisely rocket science, but it does need solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a moderately tough project. If the old bathtub is easily available, the task can relocate quickly; if you need to open up a wall to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about using one before you start. Chances are you may require a professional plumber to make tube connections.
This post will certainly help you install a new bath tub in your bathroom if you have currently acquired a new tub as well as do not need to alter the setup of your previous water supply pipes.
Your tools as well as product checklist ought to consist of the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installation


    Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to avoid stress on the tub.
    Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you use all of the supplied washers.
    Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last placement.

    Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be rather problematic due to the restricted access that is often the case.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. When the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
    Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

    Installing the Bath tub


    Utilizing the two wood boards under its feet, put the bathtub in the needed setting. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
    The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the spirit level reviews level.
    To install faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
    Turn on the water supply and also check all joints as well as new pipework for leaks and also tighten them if needed. Fill the tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
    Lastly, fix the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub ought to wait till the bath tub has been made use of at least when as this will certainly settle it right into its final setting.

    Suitable New Touches


    If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
    If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the manufacturer provided backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bath tub


    In the area where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in problems with moisture and also feasible leaks to the ceiling listed below.
    You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture relatively early if you do not take into consideration this movement before sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I'm just very occupied with A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the new page. So long as you enjoyed reading our article if you please don't forget to share it. Kudos for your time. Don't hesitate to check our site back soon.



    Additional Resources

    Report this page